Comments on: Part III – Making Programmer and Target.

By: atmega 32 serial programmer

atmega 32 serial programmer — Tue, 26 Jul 2011 11:12:31 +0000

[...] 32 serial programmer Hi, i'm building a serial programmer for my atmega32.here's the link art III – Making Programmer and Target. | eXtreme Electronics its not working with pony prog.i measured the voltage at reset pin which goes to zero when i [...]

By: avr noob

avr noob — Mon, 25 Jul 2011 21:32:47 +0000

Hello !!

Can i use with with Atmega128 (like AT90CAN128). If not, can you suggest me some other way to upload the program into the chip instead of buying ready made development board.

Please reply !!

By: chathuranga

chathuranga — Tue, 19 Jul 2011 05:05:22 +0000

thanks, i was looking for avr programmer circuit.

By: Gaurav

Gaurav — Fri, 10 Jun 2011 09:24:56 +0000

Sir
you did a good job
i have build a similar programmer
this is a serial port avr programmer

http://microembeded.blogspot.com/2011/04/avr-serial-port-programmer.html

i will provide live support for the programmer

By: Avinash

Avinash — Wed, 08 Jun 2011 02:30:51 +0000

@Prithviraj Nag

Yes if you have v2.0 of USB AVR Programmer then it mates nicely with 40 PIN DEV Board.

By: Prithviraj Nag

Prithviraj Nag — Tue, 07 Jun 2011 14:18:17 +0000

Hi, i have already purchased your AVR Programmer in the past, now i want to purchase your AVR low cost development board, can you please clarify for me one thing please?
Will i be able to connect the ISP cable from programmer to development board directly? i mean is there appropriate socket? this has always been a problem for me because my target circuit was on a breadboard and i could not conect the isp calbe properly

By: frmkla

frmkla — Thu, 05 May 2011 10:00:13 +0000

Thanks for the circuit..

By: trilok nagar

trilok nagar — Mon, 25 Apr 2011 15:59:45 +0000

thanks.thanks.thanks.

By: Avinash

Avinash — Fri, 04 Feb 2011 03:19:55 +0000

@Vignesh

See coment number 16

http://extremeelectronics.co.in/avr-tutorials/part-iii-making-programmer-and-target/comment-page-1/#comment-2024

By: Avinash

Avinash — Fri, 04 Feb 2011 03:15:19 +0000

@Vignesh

You just lost your money. This does not work with USB to Serial Converters!

By: Vignesh

Vignesh — Wed, 02 Feb 2011 18:32:53 +0000

Hi,
I need a help!!
I don’t have a serial port in my laptop…!! My friend accidentally got the burner with the above circuit.. So i bought a usb to serial converter and connected the circuit.. Then i downloaded the pony prog software. The probe test gave ok but then when i gave the write option it says device missing…..Can anybody help me out with this???

By: kaustubh

kaustubh — Mon, 24 Jan 2011 01:10:00 +0000

@ Avinash,

Hey !!
I use to hunt Dodos for lunch.
You can come to my place & we can Njoy “LUNCH” together.

By: Avinash

Avinash — Sat, 08 Jan 2011 05:45:49 +0000

@Kaustubh,

Its like hunting dodos for lunch, why not buy chickens!

Parallel ports are damn slow when used for programming ATmegas! and are more rare than dodos.
http://en.wikipedia.org/wiki/Dodo

By: kaustubh

kaustubh — Sat, 08 Jan 2011 05:18:34 +0000

Hi friends
If ur having PC with windows xp and parallel port then u can have programmer in less than Rs.100/- [INR].
[Make sure that PC is installed with Windows XP and has parallel port]
Here is all help u need to built programmer-

http://embeddedelectronicsforatmegaseries.blogspot.com/

If u saw the connectors SV1 and SV2 carefully,they are 6 pin connectors.It can be managed with 5 pin connectors also. just remove NC[No connection] pin of 6 pin connectors.

Sequence of the 6 pin connector[as shown in fig.]
MOSI
MISO
SCK
/RST
NC[No connection]
GND

Sequence of the 5 pin connector[after removing NC pin]
MOSI
MISO
SCK
/RST
GND

this is it.
if there are any queries then post it to blog

By: programer supoport for at89s52

programer supoport for at89s52 — Wed, 29 Dec 2010 08:03:49 +0000

[...] [...]

By: Avinash

Avinash — Tue, 07 Dec 2010 03:13:08 +0000

@Ahmad,

Why do such weird things? If low cost USB AVR Programmer are available through out the world. Even very easy to make? Serial Port Programmers are damn slow even when run from a real serial port!

By: ahmad

ahmad — Mon, 06 Dec 2010 23:40:26 +0000

heelo
can i use a pcmcia to serial adaptor to program the AVR?
thank you

By: gmm

gmm — Sun, 28 Nov 2010 02:13:02 +0000

Hi
Actually the maximum frecuency for the internal oscillator is 8 MHz. Check the clock options in the uc datasheet. Great tutorials btw!

By: vikas arora

vikas arora — Tue, 16 Nov 2010 16:01:54 +0000

THANKS AVINASH FOR PROVIDING SUCH A USEFUL INFORMATION. I WAS SEARCHING FOR IT FOR A LONG TIME….

By: Firefox Bookmarks « Rabiul's

Firefox Bookmarks « Rabiul's — Sat, 09 Oct 2010 19:51:13 +0000

[...] Part III – Making Programmer and Target. | eXtreme Electronics [...]